Browse all practice questions for the Pipefitter Star Practice Exam. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Pipefitter Star Practice Exam course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • What device measures the specific gravity of liquid?
  • Capillary action is used in ______ joints
  • If you double the size of a pipe, how many times does its capacity increase?
  • What does hydronics refer to?
  • On an isometric drawing, how many degrees from horizontal are horizontal pipes drawn?
  • Which of the following is an example of a first class lever?
  • In terms of fittings, what does the abbreviation "LR" stand for?
  • If an excavation is deeper than 4 feet, ______________ must be used.
  • Pneumatic transmitters operate at pressures between 3 and _____ psig.
  • What type of reducer should be used on the discharge side of the pump?
  • What component causes a pressure drop of high pressure liquid refrigerant?
  • Which is the correct way to install wire rope clamps?
  • When the dog everything signal is given, the crane operator is to ___________.
  • What is the approximate density of water in pounds per gallon?
  • The take off of any angle welded elbow is what?
  • What does MSDS stand for?
  • What type of hand signal includes pointing the thumb down to the side of the body?
  • What is the proper method to ensure a PVC joint is made correctly?
  • Type L copper tube has which color stripe?
  • A (n) ______ shall be used on the suction side of the hydronic pump.
  • When hoisting a load with sharp edges, you should use ______.
  • Which device should be used to provide support for vertical piping?
  • What can happen if an orifice plate is installed backwards?
  • What is the safety factor for rigging slings?
  • What is the volume in gallons of a cylindrical tank that is 3 feet in height and 2 feet in diameter?
  • Which component is responsible for compressing refrigerant vapor?
  • The main components of a refrigeration system that perform the heat-moving process are the evaporator and the _________.
  • What is the purpose of a rolling hanger in a steam piping system?
  • Guides are used near _____.
  • Which one is not a characteristic of a confined space?
  • Why is it necessary to use flux on a soldered joint?
  • Who is allowed to signal the crane?
  • What is the primary purpose of flux in soldering?
  • At what pipe size does the nominal sizing change from inside diameter to outside diameter?
  • What is the primary purpose of the taper on a pipe thread?
  • The beveled edge of an orifice plate is installed with the bevel _____.
  • What should you do to prepare a flange for gasket installation?
  • What is used to soften PVD pipe and remove the gloss?
  • How is ACR tube measured?
  • Which option is not a consideration for the location of a cooling tower?
  • An occupant in an excavation must have an exit point within ______ feet.
  • In a lever system, what does the distance from the fulcrum to the point of applied effort determine?
  • What is the type of refrigeration system where 100% of the refrigerant is boiled off as it leaves the evaporator?
  • When calculating the travel length of a 45 degree offset, which factor should you multiply by?
  • Soldered joints shall never be used on systems operating above _____ degrees
  • What type of fitting is required when reducing the pipe size on a horizontal steam pipe?
  • Which sling angle places the slings under the greatest strain?
  • A single line on a piping drawing represents which part of the pipe?
  • What is the term for the instantaneous change of state from liquid to vapor when a liquid flows from high to low pressure?
  • The refrigerant's state change is primarily facilitated by which component?
  • What piping arrangement prevents a boiler from draining to a dangerous level?
  • What is the effect of using too much flux on a soldered joint?
  • When working inside of a confined space, the atmosphere must be monitored _______________.
  • Which property of a substance affects how much weight it has at a given volume?
  • Which type of valve may be used as a vacuum breaker if installed backwards on a steam system?
  • A control valve may be bypassed with which type of valve?
  • What diameter does a 45 degree pipe elbow typically have?
  • If a hydronic terminal unit will not heat, what could be a possible issue?
  • How many pounds are in a cubic foot of water?
  • To convert cubic inches to cubic feet, which conversion do you use?
  • Condensate piping shall be ______.
  • What component is key to processing the information sensed throughout a control system?
  • A (n) _____ is the part of a refrigeration system that rejects heat.
  • The __________ is the portion of the process loop that makes a decision.
  • What is the rigging tool called?
  • Which component is crucial for maintaining proper flow through steam traps?
  • What is the formula for calculating the travel on a 45 degree rolling offset?
  • The four devices that make up a control loop are the primary element, the ________, the controller, and the final control element.
  • How is a reducing tee ordered?
  • Any crane signal in the palm of the hand means ________.
  • Which part of a heat exchanger changes the state of the refrigerant to 100% liquid?
  • How many directions can be found on an isometric compass?
  • Capillary action is ________.
  • Which type of refrigerant is known for not being condensable?
  • What does ACR stand for?
  • Compressed gas cylinders shall only be moved when:
  • What is the primary function of a pressure gauge?
  • On an isometric drawing, vertical pipes are drawn at what angle from horizontal?
  • The make-up water for a cooling tower must include what component?
  • The depth of a pipe thread may be tested by turning a fitting on by hand how many turns?
  • Which component in a closed control loop is the primary element?
  • What is the same as 1 cubic foot in gallons?
  • Before attaching a pressure regulator to a compressed gas cylinder, _______.
  • Steam traps operate based on which three principles?
  • What safety equipment is essential when working with compressed gases?
  • What is the primary function of the expansion device in a refrigeration system?
  • A ________ evaporator is placed in the airstream to cool and remove humidity.
  • What distinguishes a heat pump from an air conditioning unit?
  • An extension ladder must extend ______ feet above the landing.
  • How many pounds does one cubic inch of mercury weigh?
  • What is the mechanical advantage of a machine with a 6" primary pulley and an 18" secondary pulley?
  • Which component should be installed near an expansion loop in a piping system?
  • For a pipe fitting, what does the term "NPT" refer to?
  • To find the travel length of a 45 degree offset, which multiplication factor is correct?
  • When calculating offsets for piping, which angle is primarily used for standard elbows?
  • What is the standard size of a coupling used with 3" pipe?
  • When should a soldered joint be tested for leaks?
  • What is not a part of a closed control loop?
  • A (n) is a substance that moves heat by changing state from a liquid to gas when absorbing heat and from gas to liquid when rejecting heat.
  • What type of expansion joint does not utilize mechanical movement?
  • Which sling configuration provides the greatest capacity?
  • Flux is applied to a soldered joint _____.
  • A (n) _______ is the part of a refrigeration system responsible for the absorption of heat from a product or building spaces into the fluid (refrigerant) of the system.
  • What does the coefficient of thermal expansion tell us?
  • Who can give the emergency stop crane signal?
  • What does "6G" represent regarding the position angle of the weld coupon?
  • Which device uses a liquid column to measure vacuum?
  • What type of copper tube may be used in HVAC systems?
  • A centrifugal pump motor turns what component?
  • What is the color of the oxygen hose?
  • The greatest contributor to pump/motor shaft misalignment is?
  • What is the weight of one cubic foot of water in pounds?
  • Which component receives superheated vapor in a refrigeration system?
  • Fall protection must be worn when within _____ feet of a leading edge.
  • A _________ is used when returning condensate directly to the boiler is not possible.
  • When can a confined space attendant perform a rescue of a non-responsive worker?
  • What is the area of a circle with a diameter of 10 inches?
  • A single pressure control main operates at pressures between 13 and _____ psig.
  • What is considered a non-condensable in a refrigeration system?
  • A (n) _____ is a heat exchanger that transfers heat from a product or from room air into a low-temperature, low-pressure liquid gas refrigerant.
  • What is the pressure halfway up an 80 ft tall open pipe filled with water?
  • If a gallon of water occupies 0.135 cubic feet, how many gallons will a tank 3 ft long, 36 inches wide, and 4 ft deep hold?
  • How many gallons are there in one cubic foot of water?
  • A bourdon tube is found inside of a ______.
  • What happens to copper when it is annealed?
  • How far should a copper tube be inserted into a cup for a brazed joint?
  • What is NOT a final control element?
  • What type of sensor is installed directly in the process stream?
  • How should you assemble a four-bolt flange?
  • What is the area of a circle with a diameter of 18 inches?
  • If a soldered joint is overheated, _______.
  • What is the purpose of using a pipe hanger?
  • To align a flange with 8 bolt holes, which type of hole must be performed?
  • The boiler feedwater pump operates due to a ___________.
  • The pressure by a fluid at rest, due to its weight, is called what?
  • The face to center distance of a 4" welded long radius 45 degree elbow is:
  • An up feed steam heating system has the heating units _____.
  • A crane should not be loaded beyond its _____ capacity.
  • What type of knot or hitch can be used for lifting a length of small-bore pipe vertically?
  • If the pipe size is 4" and you have an offset distance of 36", what would be the cut piece length?
  • What is it called when two or more metals are mixed?
  • When observing a south elevation view on a drawing, what perspective are you viewing from?
  • What issue may arise from a horizontal pipe not being properly supported?
  • When a steam pipe crosses an I beam pipe support, which support should be installed?
  • A _____ is used to sense temperature from a distant location.
  • A control valve with two inlets and one outlet is known as a?
  • What is the radius measurement of an 8" welded long radius 45 degree elbow?
  • When loosening the bolts on a flange, which bolts should you loosen first?
  • In a refrigeration cycle, which device is responsible for removing heat from the refrigerant?
  • Convert 0/75 ft to an inch measurement. What is the correct answer?
  • The _____ is the desired value where a process should be maintained.
  • A crane cannot be within _____ feet of a power line up to 50 KV.
  • How much will a 300 ft long aluminum pipe grow in length when the temperature rises from 48 degrees to 18 degrees?
  • A fan coil utilizes what method to distribute heating or cooling to a space?
  • Which of the following represents the square root of 2?
  • What should you multiply by to determine the step ahead distance of a 45 degree equal spread offset?
  • What type of device should be installed between the isolation valve and the union on the inlet of the steam trap?
  • Which tool is commonly used for cutting copper pipe?
  • What type of hanger dampens vibration in piping systems?
  • What type of controller increases line pressure when room temperature increases?
  • What is not a basic part of a closed control loop?
  • What type of flame should be used to cut carbon steel?
  • For a 75 degree turn from a 90 degree welded long radius elbow, what is the proper layout technique?
  • What is the weight in pounds of one gallon of water?
  • High pressure condensate is piped to a ______.
  • The height of the hydronic system ______ the performance of the pump.
  • What is the maximum temperature that soldered joints can safely handle without compromise?
  • What is the best type of hanger for supporting a horizontal run of steam/condensate piping?
  • Steam piping shall be graded ______.
  • Which component stores liquid refrigerant in a refrigeration system?
  • A _______ evaporator has refrigerant surrounding the tubes and chilled water is inside the tubes?
  • Why is a bushing not considered a good replacement for a reducer?
  • What action would change on a receiver in a control system?
  • ______ is defined as the interface between peripheral equipment and digital systems.
Subscribe

Get the latest from Examzify

You can unsubscribe at any time. Read our privacy policy